Parts on Infrared UV Heater

220V 2000W Infrared Halogen Heater Parts

Fri, 17 Jul 2026 01:10:29 +0800

Let’s talk about the 220V 2000W Halogen Heater

When we built these 2000W halogen lamps, we had one goal: raw, intense heat. At 220V, these things pump out shortwave infrared. The cool part? The heat goes straight into your material. You aren’t wasting energy heating up the air in the room; you’re hitting the target directly. The power side of things Packing 2000W into a small quartz tube creates a massive amount of heat in a tiny space. It gets hot—fast. If you’re looking to replace an old industrial heating bank, these just slide right in. We stuck with a 220V setup because it plays nice with most standard industrial grids. That means you can skip the headache of messing around with bulky step-down transformers. What’s actually inside? We use high-purity quartz for the envelope and inject halogen gas inside. Here’s why that matters: normally, filaments evaporate over time. But the halogen gas actually pushes the tungsten back onto the wire. It’s a clever little trick that keeps the lamp living longer. For the connections, we usually go with R7s or SK15 bases. They just snap in. It makes the initial wiring a breeze and means you can swap a burnt-out bulb in seconds without a whole production meltdown. Real-world advice You’ll see these doing the heavy lifting in PET blowing machines or plastic curing lines. The radiation just cuts through the material. But, a word of caution. Because these are so powerful and compact, they runhot. Like, really hot. If your reflector gets dusty or your airflow is blocked, you’re going to fry the ends of the tube. Make sure your housing is built to take the heat, or you’ll end up with warped mounting brackets. Also, double-check your controllers. These lamps have a big “inrush current” when they first kick on, and if your gear isn’t rated for it, you’ll be tripping breakers every time you start a cold run.

700mm 230V 2000w Half White Reflector Halogen Lamp Replacement Parts

Sat, 27 Jun 2026 00:39:10 +0800

Introduction

We built this 700mm, 230V, 2000W Half-White Reflector Halogen Lamp to slide right into industrial heating systems. Its job? Deliver focused infrared heat in a tight footprint, keeping your process temperature steady—without straining your electrical setup.

What makes it tick

At 700mm long and 2000W, you get a heat profile you can count on, right where you need it. And because it runs on 230V, it plugs straight into standard industrial circuits—no extra transformers. That power density means it wakes up fast, so your line doesn’t sit around waiting to warm up. The half-white reflector coating isn’t just for looks. It bounces infrared forward while letting visible light through, so you get pinpoint heating with better visibility. Energy goes where it should—no waste.

Blowing machines parts quartz infrared halogen heat lamp 600mm 2000w

Thu, 23 Apr 2026 09:15:10 +0800

Introduction

We engineer the 600mm, 2000W quartz halogen infrared heat lamp specifically as a drop-in component for blowing machine parts. This unit targets the heating zones of PET and similar blow molding systems where fast thermal response, stable output, and compact footprint are mandatory. You wire it up to deliver rapid, localized heat directly to the parison or preform, without overloading the machine’s available space.

Technical Deep-Dive: Power, Voltage, and Dimensions

The 600mm length and 2000W rating are chosen to match the heating window of standard blowing machine sections. The long tube provides a continuous, uniform hot zone along the parison path, which reduces cold spots and keeps cycle times consistent. The 2000W power density gives you enough output to heat throughput without requiring a larger enclosure or major electrical changes. Voltage selection is application-driven. These lamps are typically spec’d for industrial supply voltages (commonly 230V or 400V), depending on the machine’s control panel and available circuits. Higher voltage reduces current draw for the same wattage, which lowers conductor size and simplifies wiring. However, a higher voltage, high-wattage lamp demands proper insulation and safety clearances. You must size the control gear—contactor, fuse, and terminal block—to match the continuous load, and ensure the lamp holder and wiring can handle the operating temperature.